NEC Express5800/R110f-1E Manuel d'utilisateur télécharger pdf (Page 70)

raidcmd

Step 1 Connect Physical Devices used for Easy

Configuration to the RAID Controller before executing

raidcmd if required.

4

d the result of Initialize by "oplist" and "property"

commands.

5

>

Do y

ou continue ? [yes(y) or no(n)] : yes

Initialize all of Logical Drive after creating them. You can

see the progress an

Run the above configuration.

,Logical Drive capacity is decided by the smallest Physical

Device of capacity.

Create Logical Drive #2 with different Physical Devices of

a capacity. Therefore

<Caution>

PD e252s7 [Online] SATA-HDD(SSD)

PD e252s6 [Online] SATA-HDD(SSD)

Disk Array #3

LD #3 [Online] RAID 1

PD e252s1 [Online] SATA-HDD

PD e252s0 [Online] SATA-HDD

LD #2 [Online] RAID 1

Disk Array #2

PD e252s5 [Dedicated Hot Spare] SAS-HDD

PD e252s4 [Online] SAS-HDD

PD e252s3 [Online] SAS-HDD

LD #1 [Online] RAID 5

PD e252s2 [Online] SAS-HDD

RAID Controller #1(0) LSI MegaRAID SAS 9267-8i

Disk Array #1

Step 3/3 : Confirm the contents of configuration

Do you continue ? [yes(y) or no(n)] : y

Creating Logical Drive count [ 1] : 1

Maximum Logical Drive count : 1

Do you continue ? [yes(y) or no(n)] : y

Hot Spare count : 0

Physical Device count using Logical Drive(s) [ 2] : 2

<Physical Device (Type : SATA-HDD(SSD))>

Unused Physical Device count : 2

Do you continue ? [yes(y) or no(n)] : y

Maximum Logical Drive count : 1

Creating Logical Drive count [ 1] : 1

Do you continue ? [yes(y) or no(n)] : y

Hot Spare count : 0

Physical Device count using Logical Drive(s) [ 2] : 2

<Physical Device (Type : SATA-HDD)>

Unused Physical Device count : 2

Do you continue ? [yes(y) or no(n)] : y

Creating Logical Drive count [ 1] : 1

Maximum Logical Drive count : 1

Do you continue ? [yes(y) or no(n)] : y

Hot Spare count : 1

Physical Device count using Logical Drive(s) [ 2- 4] : 3

<Physical Device (Type : SAS-HDD)>

Unused Physical Device count : 4

RAID Controller #1 LSI MegaRAID SAS 9267-8i

RAID Controller [1] :1

Step 2/3 : Set the contents of configuration

3

> raidcmd econfig

Step

1/3 : Select RAID Controller

2

Step 2 Execute "econfig" command.

Step 3 Specify the conditions on Easy

Configuration.

In step 1/3, select the RAID Controller to be

configured. Enter the RAID Controller number to be

configured.

Step 4 In step 2/3, specify the number of

Physical Devices used for Logical Drive(s) ("Physical

Device count using Logical Drive(s)") and the number

of Logical Drives to be created in the RAID Controller

("Making Logical Drive count"). If Physical Devices of

different Interface Types or Device Type exist, specify

the number of Physical Devices in each type (in the

example shown to the right, proper settings are

provided for Physical Devices of the SAS interface. If

other Physical Devices of different types exist,

perform the operation in each type).

Step 5 Step 3/3 shows the configuration of the

RAID System to be configured by the Easy

Configuration. To configure the RAID System

according to the displayed information, type "yes". To

change the configuration, type "no".

If you type "yes", the raidcmd executes the

configuration of the RAID System. After the easy

configuration is finished successfully, raidcmd

terminates normally. Making Logical Drives and Hot

Spares is now completed. See the property of each

component to check the configuration. However, the

Initialize of the Logical Drives having been created

may not be completed. The progress of initializing the

Logical Drives can be checked by using "oplist"

command. The result of initializing the Logical Drive

can be checked by RAID Log.

70

1 2 ... 65 66 67 68 69 70 71 72 73 74 75 ... 134 135

Commentaires sur ces manuels

Pas de commentaire