NEC Express5800/R120f-1M Guide de l'utilisateur Page 77
- Page / 133
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
1. Installing Internal Optional Devices
Chapter 2 Preparations
1.12
PCI Card
This server provides PCI slots for riser card (one Full Height PCI card and one Low Profile PCI card), a slot
dedicated for LOM card, and a slot dedicated for RAID controller (total four PCI cards can be mounted).
Important
You must avoid static electricity to work with the procedure below.
For
details, see Chapter 2 (1.2 Anti-static Measures).
1.12.1
Notes
Read the following notes when installing or removing a PCI card.
• Do not touch the terminals of the riser cards and the leads of electronic components with your bare
hand. Fingerprints and dust left on them cause the server to malfunction due to a connection failure or
damage to the leads.
• Available type of PCI card depends on riser card. Make sure the card type before connecting it to riser
card.
• The server provides no connector to connect an LED connector which is supplied in RAID Controller
used to indicate disk access.
• PCI slot number "1A" is assigned to the RAID controller slot, "1B" is assigned to LOM card slot, "1C" is
assigned to the riser card for Full Height PCI card, and "1D" is assigned to the riser card for Low Profile
PCI card.
• The search order for PCI bus slot on boot is as follows.
Slot 1A (dedicated to RAID Controller) → Slot 1B (LOM card slot) → Slot 1C (Full height card slot) →
Slot 1D (Low profile card slot)
• The PCI devices of the same type (including onboard PCI device) may be recognized in different order
from those described above, depending on OS or RAID Configuration Utility. Check the slot location of
PCI device by PCI bus number, device number and function number shown in the table below.
PCI device
Bus number
Device number
Function number
LOM card LAN1 (when N8104-154/155/156 is installed)
05h
0
0
LOM card LAN2 (when N8104-154/155/156 is installed)
05h
0
1
LOM card LAN3 (when N8104-154/156 is installed)
05h
0
2
LOM card LAN4 (when N8104-154/156 is installed)
05h
0
3
Slot 1A dedicated for RAID Controller
01h
0
0
PCIe slot 1C (Full height)
0Ch
0
X
PCIe slot 1D (Low profile)
40h
0
X
PCIex16 slot 1C (Full height)
81h
0
X
PCIex16 slot 1D (Low profile)
C0h
0
X
• If an additional LAN card is installed, it is hard to push the catch of the connector with your finger that is
connected to the LAN card. Disconnect the connector pushing the catch with a standard screwdriver. At
this time, be very careful for the screwdriver not to damage the LAN card.
• If a bootable device such as a PCI card or USB device is added, the boot order may change.
In BIOS Setup Utility, select HDD Priorities from Boot menu and confirm the boot order.
Boot → HDD Priorities → Check the display
If the boot device is an HDD and located under an optional RAID Controller, the display is (Bus xx Dev
00) PCI RAID Adapter. Note that the value for xx changes depending on the PCI slot where a RAID
Controller is installed.
Express5800/R120f-1M User’s Guide
77
- Express5800/R120f-1M 1
- User’s Guide 1
- Contents 3
- Trademarks 8
- License Agreement Notice 9
- UEFI NETWORK STACK 2 10
- Latest editions 12
- Safety notes 14
- Handling precautions 15
- General Description 18
- Introduction 19
- Accessories 20
- Features 21
- Names and Functions of Parts 25
- Rear View 27
- External View 28
- Internal View 29
- Motherboard 30
- Status Indicators 32
- LED on a hard disk drive 35
- LEDs for LAN connectors 36
- AC POWER LED on Power Unit 37
- Preparations 38
- Safety Precautions 39
- Anti-static Measures 40
- Removing Front Bezel 44
- Removing Top Cover 45
- TPM Kit 46
- Processor (CPU) 47
- Installation 48
- Important 49
- Replacement / Removal 53
- * Default factory settings 54
- Memory Clock 55
- Memory RAS Feature 57
- Key slot 59
- Handling precautions 68
- Removal 71
- Removing FBU 73
- LOM Card 74
- PCI Card 77
- Installing RAID Controller 84
- Optical Disk Drive 86
- Installing Top Cover 90
- Hard Disk Drive 91
- DISK LED 2 93
- DISK LED 1 93
- Power Supply Unit 95
- Installing Front Bezel 98
- Installation and Connection 99
- CAUTION 101
- Preparation 102
- (2) Removal procedure 104
- Rail stopper 104
- (3) Removing Outer Rail 105
- Connection 106
- NEC Express5800 Series 109
- Turning on the Server 110
- POST sequence 111
- POST error messages 112
- BIOS Setup Utility (SETUP) 113
- EXPRESSSCOPE Engine 3 118
- EXPRESSBUILDER 121
- Turning Off the Server 123
- Appendix 124
- Specifications 125
- 1. Specifications 126
- Chapter 4 Appendix 126
- Interrupt Lines 131
- Glossary 132
Produits connexes et manuels pour Serveurs NEC Express5800/R120f-1M
Serveurs NEC N8103-102 Manuel d'utilisateur
(60 pages)
(60 pages)
Serveurs NEC IS016-5E Manuel d'utilisateur
(87 pages)
(87 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.771 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels