Nec LT150/LT85 Manuel d'utilisateur Page 55
- Page / 62
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
E–52
4. MAINTENANCE
This section describes the simple maintenance procedures you should
follow to replace the lamp.
Replacing the Lamp
After your lamp has been operating for 1000 hours or longer, the
“Status” light in the cabinet will go on and the message will appear.
Even though the lamp may still be working, replace it at 1000 hours
to maintain optimal projector performance.
CAUTION
• DO NOT TOUCH THE LAMP immediately after it has been
used. It will be extremely hot. Turn the projector off, wait 90
seconds, and then disconnect the power cable. Allow at least
one hour for the lamp to cool before handling.
• DO NOT REMOVE ANY SCREWS except the lamp cover
screw and three lamp case screws. You could receive an elec-
tric shock.
•
The projector will turn off and go into stand by mode after 1100
hours of service. If this happens, be sure to replace the lamp. If
you continue to use the lamp after 1000 hours of use, the lamp
bulb may shatter, and pieces of glass may be scattered in the lamp
case. Do not touch them as the pieces of glass may cause injury.
If this happens, contact your NEC dealer for lamp replacement.
To replace the lamp:
1 Loosen the lamp cover screw until the screwdriver goes into a
freewheeling condition and remove the lamp cover. The lamp cover
screw is not removable.
2 Loosen the three screws securing the lamp housing until the screw-
driver goes into a freewheeling condition. The three screws are
not removable.
4 Insert a new lamp housing until the lamp housing is plugged into
the socket.
A
C
IN
PC CARD
USB
AUDIO
VIDEO
S-VIDEO
RGB
PC CONTROL
A
C
IN
PC CA
RD
USB
AUD
IO
VID
EO
S
-VID
EO
RG
B
PC
CON
TROL
A
U
D
I
O
R
G
P
C
C
O
N
T
R
O
L
Interlock
3 Remove the lamp housing by pulling out the handle.
NOTE: There is an interlock on this case to prevent the risk of electrical
shock. Do not attempt to circumvent this interlock.
AUDIO
RGB
PC CO
NTR
O
L
5 Secure it in place with the three screws.
A
U
D
I
O
S
-
V
I
D
E
O
R
G
B
P
C
C
O
N
T
R
O
L
6 Reattach the lamp cover.
A
U
D
IO
S
-V
ID
E
O
R
G
B
P
C
C
O
N
T
R
O
L
7 Tighten the lamp cover screw.
A
U
D
IO
R
G
B
P
C
C
O
N
T
R
O
L
8 After you install a new lamp, select the Main menu → [Projector
Options] → [Setup] → [Page 4] → [Clear Lamp Hour Meter] to
reset the lamp usage hours.
If the projector will not be turned on after using 1100 hours of
service, press and hold the [Help] button on the remote control for
ten seconds or longer to reset the lamp time clock to zero.
CAUTION: Do not use a lamp other than the NEC replacement lamp (LT50LP).
Order this from your NEC dealer.
Be sure to tighten the screws.
Be sure to tighten the screw.
- MultiSync LT150/LT85 1
- DECLARATION OF CONFORMITY 2
- (USA and Canada only) 3
- Micro-Portable Projector 4
- User’s Manual 4
- IMPORTANT INFORMATION 5
- Important Safeguards 6
- Installation 6
- Power Supply 6
- Cleaning 7
- Lamp Replacement 7
- Fire and Shock Precautions 7
- TABLE OF CONTENTS 8
- 1. INTRODUCTION 9
- User's 10
- (not adjustable) 12
- Top Features 13
- Terminal Panel Features 14
- Remote Control Features 15
- Remote Control Precautions 16
- CAUTION: 16
- 䊴 䊳) / (+) (–) Button 17
- 䊴 䊳 buttons move the pointer 18
- Remote sensor on the remote 20
- Presentation remote control 20
- L-CLICK/ENTER 21
- 2. INSTALLATION 22
- 2.97” (75.5mm) 23
- Wiring Diagram 24
- Connecting Your PC 25
- RGB INPUT 26
- Connecting Your DVD Player 27
- R L 28
- (Menu Language Select screen) 29
- 3.OPERATION 30
- PC CARD ACCESS 32
- Basic Operation 33
- KEYSTONE 34
- Using the Menus 35
- Using a USB Mouse 36
- Menu Tree 37
- Menu Elements 38
- Source Select 39
- Image Options 40
- 䊳 buttons 41
- Projector Options 42
- Eject button 48
- Card adapter (not supplied) 48
- CompactFlash card 48
- (not supplied) 48
- Projecting slides 50
- Multi cursor (blue marks) 51
- Preparations: 52
- Viewing Digital Images 53
- Terminology 54
- 4. MAINTENANCE 55
- 5. TROUBLESHOOTING 56
- 6. SPECIFICATIONS 58
- Cabinet Dimensions 59
- D-Sub Pin Assignments 60
- Timing Chart 61
- PC Control Codes 62
- Cable Connection 62
Produits connexes et manuels pour Projecteurs Nec LT150/LT85
Projecteurs Nec LT85 Manuel d'utilisateur
(62 pages)
(62 pages)
Projecteurs Nec HT1000 Manuel d'utilisateur
(66 pages)
(66 pages)
Projecteurs Nec LT265 Manuel d'utilisateur
(145 pages)
(145 pages)
Projecteurs Nec LT240K Manuel d'utilisateur
(152 pages)
(152 pages)
Projecteurs Nec XT5100 Manuel d'utilisateur
(52 pages)
(52 pages)
Projecteurs Nec WT600 Manuel d'utilisateur
(76 pages)
(76 pages)
Projecteurs Nec LT 100 Manuel d'utilisateur
(52 pages)
(52 pages)
Projecteurs Nec NP901W Manuel d'utilisateur
(17 pages)
(17 pages)
Projecteurs Nec MT1065 Manuel d'utilisateur
(70 pages)
(70 pages)
Projecteurs Nec GT950 Manuel d'utilisateur
(66 pages)
(66 pages)
Projecteurs Nec LT280 Manuel d'utilisateur
(40 pages)
(40 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.790 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels