NEC LCD175VXM+ Manuel d'utilisateur télécharger pdf (Page 6)

English-2

English

Figure C.1

Power Button

Figure TS.1

Figure R.1

Non-abrasive surface

Figure R.2

Figure R.3

4-SCREWS (M4)

MAX depth:

LCD175VXM+ - 7.0mm

LCD195VXM+ - 8.5mm

If use other screw,

check depth of hole.

Weight of LCD assembly: 3.8 kg - LCD175VXM+ (MAX)

5.0 kg - LCD195VXM+ (MAX)

Specifications

Replace screws

Tighten all

screws

100 mm

Thickness

of Bracket (Arm)

2.0 ~ 3.2 mm

Controls

OSM (On-Screen Manager) control buttons on the front of the monitor function as follows:

1. Basic function at pressing each key

Showing OSM. Shortcut to Bright adjust

window.

Button

At No OSD

showing

Shortcut to Volume adjust

window.

At OSD showing

(Icon selection stage)

Go to Adjustment stage. Cursor goes to left. Cursor goes to right.

At OSD showing

(Adjustment stage)

Go to Icon selection stage. Adjust value decrease or

Cursor for adjust goes to

left.

Adjust value increase or

Cursor for adjust goes to

right.

SELECT

– +

Input signal select.

Reset operation.

Mute off/on switch on

Volume adjustment window.

1<->2 / RESET

5. Connect one end of the power cord to the monitor and the other

end to the power outlet. Place the Video Signal Cable, Audio cable

and power cord to the Cable management cover (Figure B.1).

NOTE: Adjust position of cable that place under the Cable

management cover to avoid damage for cable or monitor.

NOTE: Please refer to Caution section of this manual for proper

selection of power cord.

6. Turn on the monitor with the front power button and the computer

(Figure C.1).

7. No-touch Auto Adjust automatically adjusts the monitor to optimal

settings upon initial setup for most timings. For further

adjustments, use the following OSM controls:

• Auto Adjust Contrast

• Auto Adjust

Refer to the Controls section of this User’s Manual for a full

description of these OSM controls.

NOTE: If you have any problem, please refer to the

Troubleshooting section of this User’s Manual.

Raise and Lower Monitor Screen

The monitor may be raised or lowered. To raise or lower screen, place

hands on each side of the monitor and lift or lower to the desired

height (Figure RL.1).

NOTE: Handle with care when raising or lowering the monitor

screen.

Tilt

Grasp both sides of the monitor screen with your hands and adjust

the tilt as desired (Figure TS.1).

Remove Monitor Stand for Mounting

To prepare the monitor for alternative mounting purposes:

1. Disconnect all cables.

2. Place monitor face down on a non-abrasive surface (Figure R.1).

3. Remove the 4 screws connecting the monitor to the stand and

remove the stand as indicated (Figure R.2). The monitor is now

ready for mounting in an alternative manner.

4. Connect the AC cord and signal cables to the back of the monitor

(Figure R.3).

5. Reverse this process to re-attach stand.

NOTE: Use only VESA-compatible alternative mounting method.

NOTE: Handle with care when removing monitor stand.

Connecting a Flexible Arm

This LCD monitor is designed for use with a flexible arm.

Please use the attached screws (4pcs) as shown in the picture when

installing. To meet the safety requirements, the monitor must be

mounted to an arm which guaranties the necessary stability under

consideration of the weight of the monitor.

The LCD monitor shall only be used with an approved arm (e.g. GS

mark).

100 mm

Figure RL.1

01_English 21/1/07, 12:21 PM2

1 2 3 4 5 6 7 8 9 10 11 ... 23 24

Commentaires sur ces manuels

Pas de commentaire

NEC LCD175VXM+ Manuel d'utilisateur Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Affichages LED NEC LCD175VXM+