NEC LCD175VXM+ Manuel d'utilisateur télécharger pdf (Page 5)

English-1

English

Declaration of the Manufacturer

We hereby certify that the colour monitors MultiSync LCD175VXM+

(L174F1)/LCD195VXM+ (L194F2) are in compliance with

Council Directive 73/23/EEC:

– EN 60950-1

Council Directive 89/336/EEC:

– EN 55022

– EN 61000-3-2

– EN 61000-3-3

– EN 55024

RISK OF ELECTRIC SHOCK • DO NOT OPEN

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S

POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED.

REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

WARNING

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

This symbol warns user that uninsulated voltage

within the unit may have sufficient magnitude to cause

electric shock. Therefore, it is dangerous to make any

kind of contact with any part inside this unit.

This symbol alerts the user that important literature

concerning the operation and maintenance of this

unit has been included. Therefore, it should be read

carefully in order to avoid any problems.

CAUTION

and marked with

NEC Display Solutions, Ltd.

4-13-23, Shibaura,

Minato-Ku

Tokyo 108-0023, Japan

Contents

Your new NEC MultiSync LCD monitor box* should contain the

following:

• MultiSync LCD monitor with tilt base

• Audio Cable

• Power Cord

•Video Signal Cable (15-pin mini D-SUB male to 15-pin mini

D-SUB male)

•Video Signal Cable (DVI-D to DVI-D) (LCD195VXM+ only)

• User’s Manual

• CD-ROM

• Cable management cover

Remember to save your original box and packing material to transport or ship

the monitor.

User’s

Manual

Audio

Cable

Power

Cord

15-pin mini D-SUB

male to 15-pin mini

D-SUB male

DVI-D to DVI-D

(LCD195VXM+

only)

MultiSync LCD monitor

CD-ROM

Quick Start

To pull the stand, follow these instructions:

1. Place monitor face down on a non-abrasive surface (Figure 1).

2. Pull the stand holding the monitor with the other hand until the

stand clicks (Figure 2).

NOTE: Handle with care when pulling the stand.

NOTE: Reverse this procedure if you need to re-pack the monitor.

To attach the MultiSync LCD monitor to your system, follow these

instructions:

1. Turn off the power to your computer.

2. For the PC or MAC with DVI digital output: Connect the DVI-D

signal cable to the connector of the display card in your system

(Figure A.1). Tighten all screws.

For the PC with Analog output: Connect the 15-pin mini D-SUB

signal cable to the connector of the display card in your system

(Figure A.2). Tighten all screws.

For the Mac: Connect the MultiSync Macintosh cable adapter

(not included) to the computer. Attach the 15-pin mini

D-SUB signal cable to the MultiSync Macintosh cable adapter

(Figure A.3). Tighten all screws.

NOTE: Some Macintosh systems do not require a Macintosh cable

adapter.

3. To attach the Cable management cover:

Insert the tabs of the Cable management cover into the holes of

Stand neck and slide the Cable management cover downward into

place (Figure A.4).

NOTE: Please confirm that the tabs are completely secure.

4. Connect all cables to the appropriate connector on the back of the

monitor (Figure B.1). Connect the Headphone (not included) to

the appropriate connector at the rear side of the monitor (Figure

C.1).

Figure A.1 Figure A.2

Macintosh Cable Adapter (not included)

Cable management

cover

Figure 1 Figure 2

Figure A.3

Base

Stand

Cable management cover

Figure A.4

AUDIO INPUT

D-Sub (Input1)

DVI-D (Input2)

Cable management cover

Connect to Computer

audio output

Figure B.1

01_English 21/1/07, 12:21 PM1

1 2 3 4 5 6 7 8 9 10 ... 23 24

Commentaires sur ces manuels

Pas de commentaire

NEC LCD175VXM+ Manuel d'utilisateur Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Affichages LED NEC LCD175VXM+