NEC XT9000 Manuel d'utilisateur télécharger pdf (Page 12)

E – 5

1. INPUT 3 RGB Connector (Mini D-Sub 15 pin)

Connect your PC or other analog RGB equipment such as a high-defi-

nition document camera.

This connector accepts RGB signals only.

Not compatible with component signals.

2. Option Connector (Mini D-Sub 9 pin)

For system expansion such as PC-control.

IN ................. connect to the external equipment such as PC or Third Party

Control System.

OUT ............. for daisy-chaining multiple projectors and operating them with

the same external equipment. To do so, connect to a second

projector's IN terminal to relay the input at the IN terminal of

the first projector until all the projectors are connected.

3. REMOTE 1 Connector (Mini D-Sub 15 pin)

This terminal allows external control of the projector from either the

Switcher or from an external control. When the Switcher is used, con-

nect to the REMOTE 1 terminal on the back of the Switcher.

NOTE: This projector is compatible with the ISS-6020 Switcher.

4. REMOTE 2 Jacks

IN ................. wired remote control input.

OUT ............. for daisy-chaining multiple projectors and operating them with

the same remote control. To do so, connect to a second pro-

jector' s IN terminal to relay the input at the IN terminal of the

first projector until all the projectors are connected.

5. RGB Digital Input/Output Connectors (DVI-D 24 pin)

These connectors are used for double stacking.

Use the supplied DVI-D cable to connect the OUTPUT terminal of the

first projector to the second projector's INPUT until all the projectors

are connected.

The output is TMDS non-perfect.

The output connector is used for stacking.

6. INPUT 1 and INPUT 2 Terminals (BNC)

Connect R,G,B,H (Horizontal sync) and V (Vertical sync) outputs of the

external equipment such as the Switcher. If using a component with a

combined sync (SYNC) output, connect it to the H/V terminal.

Also connect component video outputs (Y/Cb/Cr) of the external equip-

ment such as DVD player.

NOTE: The INPUT 2 terminal does not support SW1 Level and SW2 Level modes

for the ISS-6020 switcher.

7. INPUT 4 Y/Cb/Cr Terminal (RCA)

Connect component video outputs (Y/Cb/Cr, Y/Pb/Pr) of the external

equipment such as DVD player.

NOTE: This terminal accepts component signals only.

8. INPUT 5 VIDEO 1 Terminal (BNC)

Connect to the BNC video output of the external equipment such as a

VCR or laser disc player.

9. INPUT 6 VIDEO 2 Terminal (RCA)

Connect to the RCA video output of the external equipment such as a

VCR or laser disc player.

10. INPUT 8 S-VIDEO 2 Terminal (Mini DIN 4 pin)

Connect to the S-video output of the external equipment such as a

VCR with an S-video output. This terminal allows switching between S2

and S1 VIDEO input modes. See the "S-Video Mode Select" section on

page E-36 for more information.

11. INPUT 7 S-VIDEO 1 Terminal (BNC)

Connect to the Y/C separate BNC video outputs of the external equip-

ment such as a VCR or laser disc player.

12. LED Switch

Lights up the panel on both the front and the rear at the same time.

13. REMOTE3 Connectors (XLR Connectors)

Connect an extension cable such as an audio cable to control two pro-

jectors or more using the remote control. See page E-42 for the pin

assignments.

IN ................. wired remote control input.

OUT ............. for daisy-chaining multiple projectors and operating them with

the same remote control. To do so, connect to a second pro-

jector' s IN terminal to relay the input at the IN terminal of the

first projector until all the projectors are connected.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 53 54

Commentaires sur ces manuels

Pas de commentaire

NEC XT9000 Manuel d'utilisateur Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Projecteurs de données NEC XT9000