NEC NP-UM330X-WK1 Spécifications

====================================================================== Control Commands for NEC Projector (Basic) Rev 06.4.12a Copyright (C) NEC Di

LAN connection ---------------------------------------------------------------------- [ Wired LAN port ] LAN interface Communication speed: Auto s

039. LAMP MODE SET 03H B1H 00H 00H 02H 07H 00H BDH 046. WXGA MODE SETTING REQUEST 03H B0H 00H 00H 01H DATA1 CKS

29: NP4100/NP4100W (NP4100 Series) 30: NP1250/NP2250/NP3250/NP3250W (NP3250 Series) 31: NP310/NP410W/NP510/NP510W/NP510WS/NP610/NP610S (NP610 Se

Meaning of Symbols--------------------------------------------------------------------* Supported! Is available depending on model's version-

Command Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 28006. RUNNING SENSE * * * * * * * *

This will differ depending on the projector. In case of MT/NP1000 series 10H In case of MT/NP3150 series 10H In case of MT/NP3250

Command: 00H 81H 00H 00H 00H 81H Response: At the time of a success 20H 81H 01H xxH 01H DATA01 CKS (*1) (*2)

DATA02 Projector ID DATA021 .. 64 NP40001 .. 254 NP62/NP641 .. 254 NP216 DATA03 Reserved DATA04

DATA29 Picture mute 00H : OFF 01H : ON DATA30 Sound mute 00H : OFF

DATA66 Forced On-screen mute 00H : OFF 01H : ON DATA67 On-screen display 00H

====================================================================== Contents 1. Projector Control 2. Connection Method 3. Interface Condit

Data01 Data70 Data7101H 00H 03H MT1060/MT106501H 01H 03H MT86001H 02H 03H MT107501H 00H 06H NP1000/NP200002H 00H 03H LT240/LT26002H 01H 03H LT22002H 0

DATA72 PC Card insertion 00H : Not inserted 01H :

009. ERROR STATUS REQUEST ********************************************************************** Function: This command acquires the error informatio

Supplement: (!) LT/LT80/HT: "None" 015. POWER ON ********************************************************************** Function: This

DATA02 Switching number --------------------------------------------------------- When the switching object is the &qu

MT LT LT180 LT80 HT GT W T VT NP1000/3150 HT10 LT30 NP4001H RGB1(RGB) * * * * * * * * * * * *02H RGB2 (!1) * * - * - * - * * - - -02H DVI(ANALOG) (!2)

This command blanks the picture. Command: 02H 10H 00H 00H 00H 12H Response: At the time of a success 22H 10H 01H xxH 00H CKS

This command cancels the sound muting. Command: 02H 13H 00H 00H 00H 15H Response: At the time of a success 22H 13H 01H xxH 00H CKS

*volume increment/decrement *direct setting of brightness *brightness increment/decrement *direct setting of color *color increment/decrement *direct

DATA03 : 01H (increment/decrement) DATA04 : FFH (lower data : -1 = FFFF<Hex>) DATA05 : FFH (upper data : -1

(1) (2) (3-1) (3-2) (3-3) (3-4)GT5000/GT6000 Yes Yes Yes Yes Yes NoGT1150/GT2150 Yes No Yes Yes Yes NoHT410/HT510 Yes No No No No NoHT1000/HT1100 Yes

DATA01 DATA02 Adjustment items18H 00H Aspect Ratio Input (!) DATA03 Adjustment mode

037. INFORMATION REQUEST ********************************************************************** Function: This command acquires the projector in

(*1) (*2) (*3) Data Portion Contents --------------------------------------------

(*1) (*2) (*4) (*3) 037-4. LAMP INFORMATION REQUEST 3 **********************************

Calculator Procedure 1) Set calculator to HEX 2) Punch in DATA06 DATA05 DATA04 DATA03 (00004650) 3) Change from HEX to Decimal - value

DATA02 DATA03 DATA04 DATA05 : Kilogram 9CH 09H 00H 00H : 2460 [kg] DATA06 DATA07 DATA08 DATA09 : Milligram 06H

A3H 9BH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: * In case of acquiring lamp's us

Data Portion Contents ----------------------------------------------------------------- DATA01 07H fixed DATA02 Se

----------------------------------------------------------------- DATA01 C3H fixed DATA02 Setting Value

050. REMOTE KEY CODE ********************************************************************** Function: This command sends remote control key codes

* The serial cable, LAN card and LAN cable are separately sold. * The WT610 replaced the WT610 and uses the same command set. (CAUTION) Before maki

57 39H 00H INFO. 58 3AH 00H PIXEL 59 3BH

DATA01 Results 00H : Normal FFH : Error Response: At the time of a failure A2H 0FH 01H xxH 02H DA

Command: 02H 18H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ---------------

(*1) (*2) (*3) Data Portion Contents -------------------------------------------------------------------

053-3. LENS MEMORY CUSTOM SET ********************************************************************** Function: This command executes the "Use

Response: At the time of a failure A2H 1FH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 053-5. LENS M

DATA01 same values as DATA01 of the command DATA02 Results 00H : Normal 01H : Error Response: A

(! ) Acquirement itemsDATA01 DATA02 Acquirement name00H 00H Picture / Brightness01H 00H Picture / Contra

4CH 07H Color Correction / Yellow4CH 08H Color Correction / Magenta4CH 09H Color Correction / Cyan4CH 0AH Color Correction / White4DH 00H Through4EH 0

077. MUTE CONTROL ********************************************************************** Function: This command controls the mute of picture, sound a

( CAUTION ) Before making connections, set the standby mode of the projector to "NORMAL" or "Idol mode". The projector

DATA01 DATA02 DATA03 Current Models08H 00H 10H NP410008H 01H 10H NP4100W11H 00H 12H NP6411H 03H 12H NP4313H 01H 10H M300X13H 02H 10H M300W13H 05H 10H

Legacy Models01H 00H 03H MT1060/MT106501H 01H 03H MT86001H 02H 03H MT107501H 00H 06H NP1000/NP200002H 00H 03H LT240/LT26002H 01H 03H LT22002H 02H 03H

DATA05 Calendar function 00H : No function 01H or 03H : Timer function, sleep timer function

(*1) (*2) (*4) (*3) 078-3. INPUT STATUS REQUEST *******************************************

01H : Displaying DATA07 ..08 Reserved DATA09 Indicate Contents 00H = Picture signal displaying

078-5. MODEL NAME REQUEST ********************************************************************** Function: This command acquires the model name of t

Function: This command controls the freeze. Command: 01H 98H 00H 00H 01H DATA01 CKS Operation types DATA01: 00H : Reserved 01

Data Portion Contents ------------------------------------------------------------------- DATA01 C5H fixed DATA02 Acquisition

if DATA02 is SOURCE(02H) 00H : OFF 01H : VIDEO 02H : S-VIDEO Re

111. AUTO ADJUST EXECUTE2 ********************************************************************** Function: This command executes the Auto Adjust. Co

| |<--------------| | +--------------+ Response +--------------+ (ACK or NAK) 4-1. Frame For

DATA02 DATA03 DATA13 DATA14 Current Models03H 08H 00H 10H NP410003H 08H 01H 10H NP4100WFFH 11H 00H 12H NP64FFH 11H 03H 12H NP43FFH 13H 01H 10H M300XFF

Legacy Models00H 01H 00H 03H MT1060/106500H 01H 02H 03H MT86000H 01H 02H 03H MT107500H 01H 00H 06H NP1000/NP200000H 02H 00H 03H LT240/LT26000H

DATA15 ... 16 Reserved Response: At the time of a failure A0H BFH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2)

0CH : DIGITAL2 0DH : SCART 10H : AUTO FFH : Not Source Input

====================================================================== 6.1. Response ----------------------------------------------------------------

Entering 00H or FFH becomes a common command for all the projectors. (broadcast notification) This is convenient for controlling multiple projector

Command : This sets data length of data added to a command to send it. ( See each command description.) Response : This sets data length of data

03H : Gain-related error 04H : Logo transfer error DATA02 Error description * When not supported 00H : U