Installation Guide (Windows) Express Report Service / Express Report Service (HTTPS) EXP_E-IG-W-003-01-006 © NEC Corporation 2014 Express R
10 System Requirements 2.Express Report Service requires the following hardware and software: 1) Hardware - Memory 18.0 MB or more - Free ha
11 Express Report Service Installation This chapter explains installation of Express Report Service. 1. Installation Describes about installation p
12 Installation 1.Express Report Service must be installed after the installation of NEC ESMPRO Agent or NEC ESMPRO ServerAgentService (Service Mode
13 3. Click [Applications]. 4. Click [Express Report Service] and then [Install]. The installer starts, and the following screen is disp
14 5. Click [Continue]. 6. When Express Report Service summary is displayed, click [Continue]. 7. Select already contract and click [Co
15 8. Setup Report Opening CD (or FD) in an appropriate drive and click [Continue]. In case that Report Opening CD (or FD) has not arrived yet
16 - In case of failure read-in of Report Opening CD (or FD), the following window is displayed. * For Report Opening CD, read [Report Opening FD] o
17 10. Click [Next] and confirm the content of registration. Confirm the setting content of [Report Opening CD (or FD)] displayed on the window. Whe
18 ♦ Confirming an installation state of Express Report Service To activate Express Report Service in the condition that it has been already install
19 4. Click [Finish]. Express Report Service Setting utility starts. 5. Confirm the displayed content of Opening FD (or Opening CD). After co
2 Contents Contents ...
20 Setting Utility 2.Setting utility of Express Report Service can be used to confirm the content of Report Opening CD (or FD) while installing the
21 3. Input customer Information. When clicked the edit box of each item with a mouse, help texts are displayed at the bottom of a setting window
22 4. Input Computer Information. Product Code is selectable from the list. When the product Code is not found, you can input it directly. When c
23 5. Input the Option Parts Information. When clicked [Add], Option Parts information is settable. To delete option parts information, select th
24 6. Input Dealer Information. Dealer Information is selectable from the list. When Dealer Information is not found, you can input it directly.
25 Report method setting 3.3.1 Report setting (Internet Mail Setting) When you use Express Report Service via E-mail, follow the instruction below
26 3. Select [Express Report Service] from Report method list in [Report] property, then click [Configure...]. [Express Report Base setting] w
27 5. Enter the host name or IP address of Mail Sever that SMTP is available. Type for example: ˝smtp.foo.co.jp ˝ or ˝192.168.0.100 ˝ 6. Spec
28 8. Click [OK] to return to [Express Report Base setting] window. 9. Click [OK] on [Express Report Base setting] window to close the window
29 14. Confirm the destination and Encode and Setting Information. As a destination, the one specified on Opening CD (or Opening FD) is shown. Do no
3 Report method setting ...
30 16. Confirm the sending address of Test Report and click [OK]. 17. When the confirmation message is displayed, click [OK] to execute Test Repo
31 23. Message box is displayed, asking if the report method should be activated. Click [Yes]. If you click [NO], select [Base Setting] in Alert
32 3. Select [Express Report Service] from Report method list in [Report] property, then click [Configure...]. [Express Report Base setting] w
33 5. Click [Report Configure…]. [Report Condition Setting (COM Port)] window is displayed. Confirm the setting status. 6. Click [OK] to re
34 12. Message box is displayed, asking if the report method should be activated. Click [Yes]. ” If you click [No], select [Base Setting] in Alert
35 2. Select [Base Setting] in [Setting] menu from Alert Manager. 3. Select [Express Report from Manager] from Report method list on [Repor
36 5. Enter the address of Support Center. Click [Register…] to start [License Key reading tool]. * For Report Opening CD, read [Report Openin
37 11. SMTP server is a case of necessity about POP Before SMTP, [POP Before SMTP] is checked. SMTP server is a case of necessity about SMTP, [SMTP
38 15. Select [Express Report Service] and click [Modify ID...]. 16. [ID Setting] window is displayed. Click [Address...] [Express Report from
39 17. Click [Address…]. 18. Confirm the destination and Encode. As a destination, the one specified on Opening FD (or Opening CD) is shown. Do n
4 Notations Used in This Document Notations used in the text In addition to safety-related symbols urging caution, 3 other types of notations are us
40 ♦ Via Dial-up This section describes the report setting procedure of Express Report Service (using Dial-up) for reports forwarding Manager. 1.
41 4. Specify the port number used for the connection to Agent. Default value is set to 31136. Do not modify the default except for any necessary
42 9. Click [Report Configure…]. [Report Condition Setting (COM Port)] window is displayed. In [Serial Port], specify the serial port that is
43 ♦ Agent Side This section describes the setting procedure of Express Report (forwarding Manager) at NEC ESMPRO Agent or NEC ESMPRO ServerAgentSer
44 4. Select [Forward Manager], then click [OK] to close the window. 5. On [Base Setting] window, click [OK] to close the window. 6. On
45 9. On [Express Report Service Setting] window, click [Address…]. [Express Report (Forward Manager) setting] window is displayed. 10. Specif
46 17. On [Express Report Service Setting] window, click [OK] to close the window. 18. On [ID Setting] window, click [Schedule...] to specify ˝Retr
47 To stop Express Report Service 4.When Express Report Service is started, it permits you to click [Stop the service…]. A failure of [Stop the serv
48 Express Report Service Uninstallation This chapter explains uninstallation of Express Report Service. 1. Uninstallation Describes about uninstal
49 Uninstallation 1.Start uninstallation after the system starts completely. If uninstallation is conducted right after the system startup, it may f
5 Abbreviations of Operating Systems Windows Operating Systems (OS) are referred to as follows. Notations in this document Official names of Window
50 4. Click [Express Report Service] and then [Install]. The installer starts, and the following screen is displayed. A window below presented
51 Express Report Service Appendix 1. Note Describes about note when using Express Report Service. 4 4
52 Notes 1. ♦Uninstalling NEC ESMPRO Agent or NEC ESMPRO ServerAgentService Express Report Service must be uninstalled prior to uninstalling of NEC
53 ♦ Display of Report Settings When installed on the same machine NEC ESMPRO Manager and NEC ESMPRO ServerAgentService, [Report Settings] will be d
54 Express Report Service (HTTPS) General Description This chapter explains Express Report Service (HTTPS). 1. Introduction 2. System Requirements
55 Introduction 1.Read this document so as to gain an adequate understanding of the contents. The contents in this document are intended for users w
56 System Requirements 2.Express Report Service (HTTPS) requires the following hardware and software: 1) Hardware HTTPS: - Memory 20.0 MB or m
57 Express Report Service (HTTPS) Installation This chapter explains installation of Express Report Service (HTTPS). 1. Installation Describes abou
58 Installation 1.Express Report Service (HTTPS) must be installed after the installation of NEC ESMPRO Agent or NEC ESMPRO ServerAgentService (Serv
59 3. Click [Applications]. 4. Click [Express Report Service (HTTPS)] and then [Install]. The installer starts, and the following screen
6 Trademarks EXPRESSCLUSTER is a registered trademark of NEC Corporation. Microsoft, Windows, and Windows Server are registered trademarks or trade
60 5. Click [Next]. 6. Click [Install]. Installation starts, showing the following window. 7. When the installation end window appea
61 ♦Confirming an installation state of Express Report Service (HTTPS) To confirm if Express Report Service (HTTPS) is installed, follow the procedu
62 Setting Utility 2.This section describes the setup procedure to start Express Report Service (HTTPS). 1. Click [Start] menu - [Report Setting
63 4. Click [Load Opening file]. 5. [Express Report Service (HTTPS)Setup Utility] is displayed. Input the folder name where the Opening fil
64 7. Click [Next] in order of precedence and confirm the setting content of Opening file. When any discrepancy or unspecified item is found, mod
65 Report method setting 3.3.1 Report setting (HTTPS Setting) When you use Express Report Service (HTTPS) via HTTPS, follow the instruction below
66 4. Select [HTTPS] and click [Configure]. 5. When you use a proxy server, select [Specify a Proxy Server to Use]. Then input the address
67 8. When necessary settings for proxy server and Report Suppress are finished, click [OK] and close [Express Report Service (HTTPS) base settin
68 13. Click Primary [Test Report]. [Select address to send Test Report result] window is displayed. 14. When the address of destination is corre
69 16. Click [Opening report] and do Opening report. When any syntax error exists in Log-gathering setting file or Configuration information file, a
7 Warnings and Additions to This Document 1. Unauthorized reproduction of the contents of this document, in part or in its entirety, is prohibited.
70 When the Opening report is finished, the following message is displayed. When Configuration information file exists, the report of the configurat
71 19. Click [OK] on [Destination Setting] window. When the report method [Express Report Service (HTTPS)] is valid, [Destination Setting] window is
72 3.2 Report setting (Forward Manager Setting) This section describes the report setting procedure of Express Report Service forwarding NEC ESMPR
73 4. Specify the port number used for the connection to Agent Side. Default value is set to 31138. Do not modify the default except for any nece
74 9. Click [Address…]. [Express Report (HTTPS) from Manager Destination setting] window is displayed. 10. Store the destination definition file
75 ♦ Agent Side This section describes the setting procedure of Express Report (HTTPS)(forwarding Manager) at NEC ESMPRO Agent or NEC ESMPRO ServerA
76 4. Select [Forward Manager]. 5. When you suppress reports, click [Report Suppress]. [Report Suppress] window is displayed. To suppress t
77 9. Select [Express Report Service (HTTPS)] from ID list and click [Modify ID…]. [ID Setting] window is displayed 10. Click [Address…]. [Ex
78 13. Click [Test Report]. [Select address to send Test Report result] window is displayed. 14. When the address of destination is correct, clic
79 16. Click [Opening report] and do Opening report. When any syntax error exists in Log-gathering setting file or Configuration information file, a
8 Express Report Service General Description This chapter explains Express Report Service. 1. Introduction 2. System Requirements Describes about
80 When the Opening report is finished, the following message is displayed. When Configuration information file exists, the report of the configurat
81 19. Go back to [Destination Setting] window. Click [OK] on [Destination Setting] window. When the report method [Express Report Service (HTTPS)]
82 To Stop Express Report Service (HTTPS) 4.When Express Report Service (HTTPS) is started, it permits you to click [Stop the service…] A failure of
83 Express Report Service (HTTPS) Uninstallation This chapter explains uninstallation of Express Report Service (HTTPS). 1. Uninstallation Describe
84 Uninstallation 1.This section describes the procedure of uninstallation of Express Report Service (HTTPS). Start uninstallation after the system
85 4. Click [Express Report Service (HTTPS)] and then [Install]. 5. Choose [Remove] and click the [next]. 6. Click [Yes] and it conti
86 Express Report Service (HTTPS) Appendix 1. Definition file When Express Report Service (HTTPS) is used, the definition file is being explained.
87 Definition file 1. ♦ Destination definition file (AMHTPADR.INF) AMHTPADR.INF is a file that defines report destination of HTTPS Report Method. Be
88 ♦ HTTPS report definition file; Log-gathering/Log report function Concerning log information reported in conjunction with failure information, sp
89 1. In [Configuration] section, specify parameters. - In ˝Timeout ˝, specify number of seconds to stop collecting failure information. - In ˝Ma
9 Introduction 1.Read this document so as to gain an adequate understanding of the contents. The contents in this document are intended for users wh
90 4. In [ToolYYY] section (YYY is any of the sequence number from ˝001 to 999˝), specify individual log command. - In ˝Command ˝, specify the ab
91 ♦ Configuration information file; Configuration information report function To detect failure in advance, this function permits you to gather and
92 3. In [Schedule] section, specify the timing of gathering information. - In ScheduleType, when ˝every month˝ is given, the information is gath
93 Notes 2. ♦ Uninstalling NEC ESMPRO Agent or NEC ESMPRO ServerAgentService Express Report Service (HTTPS) must be uninstalled prior to uninstallin
94 ♦ Port number list In addition, following ports are used: - 31138 When used the Report Service (forwarding Manager). Usage of security softwa
NEC Express Server Express Report Service / Express Report Service (HTTPS) Installation Guide (Windows) NEC Corporation 7-1 Shiba 5-Chome,
Commentaires sur ces manuels