search

NEC Express5800/R120a-1 Guide de l'utilisateur Page 95

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 572
  • Table des matières
  • DEPANNAGE
    •
  • MARQUE LIVRES
    • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 94
Chapter 4
Configuring Your Server
Configuration and setup utilities are used to change your system configuration. You can configure
your system, as well as option boards you may add to your system, using the BIOS SETUP Utility.
Several unique system parameters are configured using the BIOS SETUP, which is stored in the
system FLASH memory.
The RAID configuration utility configures the RAID System and logical drives connected to the
Onboard RAID Controller or Internal RAID Controller.
If your system has been factory configured, the BIOS SETUP or RAID configuration utility do not
need to be run unless you want to change the password or security features, add certain types of
option boards or devices, upgrade your system board, or change the RAID configuration.
This chapter also provides information on several system configuration parameters that are set by
jumpers on the system board. However, these parameters do not usually require change.
SYSTEM BIOS (SETUP)
The SETUP utility is used to change system configuration parameters. This utility is pre-installed in
the flash memory of the server and ready to run.
The server is configured with the correct parameters using the SETUP utility and shipped in the best
conditions. Thus, you don't need to use the SETUP utility in most cases. However, you might wish
to use the SETUP utility in the cases described below.
IMPORTANT:
The SETUP utility is intended for system administrator use only.
The SETUP utility allows you to set a password. The server is
provided with two levels of password: Supervisor and User. With
the Supervisor password, you can view and change all system
parameters of the SETUP utility. With the User password, system
parameters available for viewing and changing are limited.
Do not set any password before installing the OS.
The server contains the latest version of the SETUP utility. Dialog
boxes appear on your SETUP utility, thus, may differ from
descriptions in this manual. If you find anything unclear, see the
online help or ask your service representative.
Use the Exit menu when exiting the SETUP utility. Exiting the
utility with the POWER switch or reset operation causes the stored
parameters to lose.
Vue de la page 94
1 2 ... 90 91 92 93 94 95 96 97 98 99 100 ... 571 572

Commentaires sur ces manuels

Pas de commentaire
Produits connexes et manuels pour Serveurs NEC Express5800/R120a-1
Serveurs NEC Express5800/R120e-1M Guide de l'utilisateur   (138 pages)
Serveurs NEC Express5800/R120d-2E SR Guide d'installation   (39 pages)
Serveurs NEC N8100-1706F Fiche technique   (41 pages)
Serveurs NEC E85NSD4-0004Z05 Fiche technique   (2 pages)
Serveurs NEC E81NMSD-0004F02 Fiche technique   (1 pages)
Serveurs NEC EB5NNLU-000BZ02 Fiche technique   (2 pages)
Serveurs NEC R120e-1E Manuel   (45 pages)
Serveurs NEC GT110d Manuel   (26 pages)
Serveurs NEC R120B-1 Manuel   (35 pages)
  • TEXET VideoLabs White Mountain Hearth Wide Bank Dimas
  • HP Articles sanitaires American Standard Robinets HP Cartes/adaptateurs d'interface National Instruments Mise en réseau Nikon Caméras de surveillance de documents
  • Samsung QM98F Thuraya SatSleeve for iPhone Zenith 12 XP Tristar VE-5930 Uniden USC230
  • Amd Athlon 27493 Manuel de l'utilisateur HP Tango Manuel de l'utilisateur Panduit QPPBBL Manuel d'installation Xerox 7232 Manuel de l'utilisateur Projecta HomeScreen Manuel