search

Nec MultiSync MT840 Manuel d'utilisateur Page 12

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 42
  • Table des matières
  • DEPANNAGE
    •
  • MARQUE LIVRES
    • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 11
E–12
2. INSTALLATION
This section describes how to set up your MultiSync MT840/MT1040
projector and how to connect video and audio sources.
Setting up Your Projector
Your MultiSync MT840/MT1040 Projector is simple to set up and
use. But before you get started, you must first:
1. Determine the image size.
2. Set up a screen or select a non-glossy white wall onto which you
can project your image.
Carrying the Projector: Always carry your projector by the handle.
Ensure that the power cable and any other cables connecting to video
sources are disconnected before moving the projector.
When moving the projector or when it is not in use, cover the lens
with the lens cap.
Screen
Top view
Screen
Side view
Using a Tabletop or Cart
1. Place your projector on a flat level surface at the optimal distance
from the screen or wall so you realize the size image you want.
(Avoid having bright room lighting or sun light directly on the
screen or wall where you’ll be projecting the image.)
4. Move the projector left or right to center the image horizontally
on the screen.
5. To center the image vertically, lift the front edge of the projector
and press the One-Touch Tilt button on the front-left side of the
projector, just above the foot, to release the Front Adjustable foot.
(There is approximately 5 degrees of up and down adjustment for
the front of the projector.)
Selecting a Location
The further your projector is from the screen or wall, the larger the
image. The minimum size the image can be is approximately 30"
(0.76 m) measured diagonally when the projector is roughly 4 feet
(1.3 m) from the wall or screen. The largest the image can be is 300"
(7.6 m) when the projector is about 36.8 feet (11.2 m) from the wall
or screen.
Lens cap
String
Rivet
Attaching the lens cap to the lens hood
with the supplied string and rivet.
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
POWER
STATUS
ON
/
OFF
SOURCE AUTO ADJUST
USB
AC IN
2. Connect the power cable, remove the lens cap and turn the projec-
tor on. (If no input signal is available, the projector will display a
background image.)
3. Ensure that the projector is square to the screen.
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
POWER
STATUS
ON
/
OFF
SOURCE
AUTO ADJUST
AC IN
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
POWER
STATUS
ON
/
OFF
SOURCE
AUTO ADJUST
AC IN
Press and hold the Tilt but-
ton on the left side of the
projector.
Lift the front edge of the projec-
tor to the height you want, and
release the button to lock the
Adjustable Tilt Foot.
Adjusting the Tilt Foot
To fine-tune the image’s position vertically on the screen,
rotate the foot. Each of the rear feet height can be changed
up to 0.6” (4mm).
6. If the projected image does not appear square to the screen then
use keystone correction for proper adjustment.
7. Adjust the size of the image using the Zoom ring on the lens.
Carrying handle
Vue de la page 11
1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 41 42

Commentaires sur ces manuels

Pas de commentaire
Produits connexes et manuels pour Projecteurs Nec MultiSync MT840
Projecteurs Nec MultiSync MT810 Manuel d'utilisateur    (20 pages)
  • My Mold Detective Safe Grow Phone-labs-technology-company Datex-Ohmeda SEIKI Digital
  • Jet Tools Outils électriques Audiovox Haut-parleurs portables Hamilton Watch Montres AMX Non Bell Équipement musical supplémentaire
  • Electrolux EW6F421B Tripp Lite B126-004 Whirlpool SF216LXSQ
  • Samsung SM-T800 Manuel de l'utilisateur Sony CMT-BX77DBi Manuel de l'utilisateur Chevrolet 2005 Astro Spécifications Mitel 4125 Manuel de l'utilisateur Yamaha RX-V2067 Guide de démarrage rapide