Nec LT154 Manuel d'utilisateur Page 27
- Page / 60
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
E – 24
3. OPERATION
Connecting the Power Cable and Turn on the
Projector
Before you turn on your projector, ensure that the computer or video
source is turned on and that your lens cap is removed.
1. Connect the supplied power cable to the projector.
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
PO
W
E
R
STATUS
O
N
/
S
TAN
D BY
S
OURCE
AUTO
AD
JUST
PC CARD
ACCESS
AC IN
C CARD
USB
PC CONTROL
VIDEO S-VIDEO RGB
AUDIO
Plug the supplied power cable in the wall outlet. The projector will
go into its standby mode and the power indicator will glow orange.
2. Turn on and off the Projector
VIDEO S
-
VIDEO
AUTO ADJ.
RGB 1
MENU LASER
RGB 2 P
J
ONOFF
Power ON button
M
E
N
E
N
T
E
R
C
A
N
C
E
L
SELECT
POWER
STATUS
ON
/
STAND BY
SOURCE
AUTO
ADJUST
PC CARD
ACCESS
PC CONTROL
VIDEO
S-VIDEO
Power ON/STAND BY button
Indicator
To turn on the projector:
Only after you press the “On” button on the remote control (“ON/
STAND BY” button on the projector cabinet) will the power indicator
turn to green and the projector become ready to use.
NOTE: To turn the projector on by plugging in the power cable, use the
menu and enable the “Auto Start” feature. (See page E-38.)
NOTE: Immediately after turning on the projector, screen flicker may occur.
This is not a fault. Wait 3 to 5 minutes until the lamp lighting is stabilized.
To turn off the projector:
First press the “off” button on the remote control (“ON/STAND BY”
button on the projector cabinet) for a minimum of two seconds. The
power indicator will glow orange. After the projector turns off, the
cooling fans keep operating for one minute.
NOTE: Do not disconnect the power cable during this time. Then, unplug
the power cable. The power indicator will go out.
Status of indicator light: turn on
POWER
STATUS
POWER
STATUS
ON
/
STAND BY
POWER
STATUS
High-Bright mode:
stand by
steady orange light
flashing green light
steady green light
flashing one minute
steady light
Eco mode:
POWER
STATUS
POWER
STATUS
POWER
STATUS
ON
/
STAND BY
stand by
steady orange light
flashing green light
(High-Bright mode)
steady green light
(Eco mode)
flashing one minute
steady light
Status of indicator light: turn off
ON
/
STAND BY
POWER
STATUS
POWER
STATUS
POWER
STATUS
ON
steady green light
change to flashing
green light
steady orange light
cooling down
stand by
Press a minimum
of two seconds.
- MultiSync LT156/155/LT154 1
- (USA and Canada only) 2
- DECLARATION OF CONFORMITY 3
- LCD Projector 4
- User’s Manual 4
- IMPORTANT INFORMATION 5
- TABLE OF CONTENTS 7
- 1. INTRODUCTION 8
- What's in the Box? 9
- Front/Side Features 10
- Rear/Side Features 11
- Top Features 12
- Terminal Panel Features 13
- Remote Control Features 14
- Remote Control Precautions 16
- Using Remote Mouse Receiver 17
- L-CLICK/ENTER 18
- 2. INSTALLATION 19
- Distance Chart 20
- Wiring Diagram 21
- Connecting Your PC 22
- Mac's video port 23
- Connecting Your DVD Player 24
- (not supplied) 25
- About Startup screen 26
- (Menu Language Select screen) 26
- 3. OPERATION 27
- 3. Adjust a Projected Image 28
- Basic Operation 30
- MENU LASER 31
- R-CLICK /CANCEL 31
- Using the Menus 32
- Using a USB Mouse 33
- Menu Tree 34
- Menu Elements 35
- Source Select 36
- Projector Options 39
- Before Installing 45
- Installation 45
- 3. Project slides 46
- Auto Play Mode 47
- Deleting Captured Images 48
- Viewing Digital Images 48
- Uninstalling the software 49
- Terminology 50
- Replacing the Lamp 51
- 4. MAINTENANCE 51
- To clean the air-filter: 52
- 5. TROUBLESHOOTING 53
- Condition Status 54
- 6. SPECIFICATIONS 55
- 207 (8.15") 56
- 40.35 (1.59") 56
- 5 (0.2") 56
- D-Sub Pin Assignments 57
- Timing Chart 58
- Cable Connection 59
- PC Control Codes 59
- Printed in Japan 60
- 7N8P0203 60
Produits connexes et manuels pour Projecteurs Nec LT154
Projecteurs Nec MT830 Manuel d'utilisateur
(48 pages)
(48 pages)
Projecteurs Nec LT150Z Manuel d'utilisateur
(62 pages)
(62 pages)
Projecteurs Nec LT170 Manuel d'utilisateur
(45 pages)
(45 pages)
Projecteurs Nec M350X Manuel d'utilisateur
(155 pages)
(155 pages)
Projecteurs Nec WT Manuel d'utilisateur
(2 pages)
(2 pages)
Projecteurs Nec GT2000 Manuel d'utilisateur
(87 pages)
(87 pages)
Projecteurs Nec NP-P350X Manuel d'utilisateur
(222 pages)
(222 pages)
Projecteurs Nec MT1040 Manuel d'utilisateur
(42 pages)
(42 pages)
Projecteurs Nec LT180 Manuel d'utilisateur
(73 pages)
(73 pages)
Projecteurs Nec MT 820 Manuel d'utilisateur
(44 pages)
(44 pages)
Projecteurs Nec LT260 Manuel d'utilisateur
(149 pages)
(149 pages)
Projecteurs Nec NP41 Manuel d'utilisateur
(100 pages)
(100 pages)
Projecteurs Nec GT1150 Manuel d'utilisateur
(79 pages)
(79 pages)
Projecteurs Nec LT150 Manuel d'utilisateur
(59 pages)
(59 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.852 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels