NEC X464UNV Manuel d'utilisateur télécharger pdf (Page 26)

English-24

TILE MATRIX Allows one image to be expanded and displayed over multiple screens (up to 100) through a

distribution ampliﬁ er.

NOTE: Low resolution is not suitable for tiling to a large number of monitors. You can operate

without a distribution ampliﬁ er at a lower number of screens.

NOTE: This function is released when selecting IMAGE FLIP except for NONE.

When “DYNAMIC” or “ZOOM” is selected in ASPECT while executing TILE MATRIX, the setting

will be applied after completing of TILE MATRIX.

H MONITORS Number of monitors arranged horizontally. 1

V MONITORS Number of monitors arranged vertically. 1

POSITION Select which section of the tiled image to be displayed on the monitor. 1

TILE COMP Turns the TILE COMP feature on. NO

TILE MATRIX ENABLE Enables Tile Matrix. NO

FRAME COMP Sets the tiled image timing to be displayed on the monitor. Large number makes large inﬂ uence

to displayed image.

NOTE: If FRAME COMP is set to AUTO or MANUAL, V SCAN REVERSE is not available.

NONE

NONE FRAME COMP is not available.

AUTO Sets display timing to vertical direction of all monitors automatically.

MANUAL Sets display timing to individual monitor.

V SCAN REVERSE Reverse scanning image direction. Normal scanning direction is top to bottom.

NOTE: If V SCAN REVERSE is set to AUTO or MANUAL, FRAME COMP is not available.

NONE

NONE V SCAN REVERSE is not available.

AUTO Sets automatically calculated image scanning direction to all monitors.

MANUAL Sets scanning direction to individual monitor.

NON REVERSE Sets normal scanning direction and delays 1 frame display image timing.

REVERSE Reverse scanning direction to individual monitor.

TILE MATRIX MEM When “INPUT” is selected, TILE MATRIX setting is applied to each signal input. COMMON

AUTO TILE MATRIX

SETUP

Allows auto setting of multiple screens by inputting the number of monitors arranged horizontally

and vertically on the primary monitor. Following settings are set automatically: MONITOR

ID, TILE MATRIX, TILE MATRIX MEM, Input Signal, VIDEO OUT SETTING, DisplayPort in

TERMINAL SETTING.

NOTE: All monitors which follow in the chain with LAN should be ON. When executing this

function while in standby mode or power save mode, “LAN POWER” should be set to ON.

AUTO ID will be automatically executed. When you use this function, it is recommended that

monitors are chained by DisplayPort cable.

Example of installation via LAN:

H MONITORS 3

V MONITORS 3

Primary monitor

DEACTIVATE

POWER ON DELAY Adjusts the delay time between being in “standby” mode and entering “power on” mode.

DELAY TIME “POWER ON DELAY” can be set between 0 and 50 seconds. 0 SEC.

LINK TO ID When “ON” selected, delay time is linked with Monitor ID. It takes more time as larger ID number. OFF

VIDEO OUT SETTING Enables the signal output from DPORT. See also page 26 “DisplayPort” in TERMINAL SETTING.

NOTE: When VGA or Y/Pb/Pr is selected as the main picture, nothing will be output from DPORT.

When this function is ON, DPORT cannot be selected as the sub picture. When this function is

ON, INPUT CHANGE is limited to be NORMAL or QUICK. When this function is ON and DPORT

is selected as the main picture, PIP CHANGE button of remote control (see page 11) is disabled.

POWER INDICATOR Turns ON or OFF the LED located at the back of the monitor.

If “OFF” is selected, LED will not light when the LCD monitor is in active mode.

SETTING COPY In a daisy chain scenario, select the OSD menu categories that you want to copy over to the

other monitor.

NOTE: When you use this function, monitors should be daisy chained by LAN. This function

resets to default when power is off. This function has a limit depending on the cable you use.

COPY START Select “YES” and press the SET button to start copying.

ALL INPUT All input terminals settings are copied when you select this item. Default is off.

RESET Resets “MULTI DISPLAY” options back to factory settings except for POWER ON DELAY and

VIDEO OUT SETTING.

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 52 53

Commentaires sur ces manuels

Pas de commentaire

NEC X464UNV Manuel d'utilisateur Page 26

Commentaires sur ces manuels

Produits connexes et manuels pour Affichages publics NEC X464UNV